command. This is used for the session, window and pane for all commands
in the command sequence if there is no -t or -s.
However, using it for all commands in the command sequence means that if
the active pane or current session is changed, subsequent commands still
use the previous state. So make commands which explicitly change the
current state (such as neww and selectp) update it themselves for later
commands. Commands which may invalidate the state (like killp) are
already OK because an invalid state will be ignored.
Also fill in the current state for all key bindings rather than just the
mouse, so that any omissions are easier to spot.
will suppress root key table bindings. So change to always check the
root table if no binding is found in the current table (whether it be
the prefix table from pressing the prefix or the copy mode table from a
pane).
A root key binding can be blocked by binding the key to a command that
does nothing (like send-keys with no arguments).
Problem reported by Thomas Sattler.
bind q select-pane -U \; resize-pane -Z
(There is still some possible weirdness with the way we do current
targets, it should probably be done in a different way at some point.)
reasonable amount (currently width * height * 8 bytes), discard all
output to the terminal and start trying to redraw periodically
instead. Continue with this until the amount of data we are trying to
write falls to a low level again.
This helps to prevent tmux sitting on a huge buffer of data when there
are processes with fast output running inside tmux but the outside
terminal is slow.
A new client_discarded format holds the amount of data that has been
discarded due to this mechanism.
The three variables (when to start this, when to stop, and how often to
redraw) are basically "works for me" at the moment, this is going in to
see how it goes and if it causes problems for anyone else.
with of the terminal scrolls, tmux needs to redraw the entire pane. This
results in a large amount of output data which can cause slow terminals
to struggle, particularly when many lines are scrolled together quickly.
This can be reduced by only redrawing when tmux doesn't hold any
buffered data for the terminal. If a redraw is required and data is
buffered, the redraw is deferred until all that data is consumed (it is
checked after every event loop, a timer is used to ensure this happens
at some point). While a redraw is pending, no additional data will be
written to the terminal.
The redraw still happens, now it is just pushed back if it is possible
it would just add more data on top of a terminal that is already
behind. This both gives the terminal a chance to catch up, and allows
tmux to process more scrolling (that would require additional redraws)
in the meantime.
Helps with a problem reported by Greg Hurrell.
falls back to an alternative if the tty name is not available. This is
clearer than overloading the client ttyname member and allows us to
remove the path stored in the tty struct, it should always be the same
as the client.
jobs, this means that if the same job is used for different windows or
panes (for example in pane-border-format), it will be run separately for
each pane.
main issue is that if we have two panes, A with 1002 and B with 1003, we
need to set 1003 outside tmux in order to get all the mouse events, but
then we need to suppress the ones that pane A doesn't want. This is easy
in SGR mouse mode, because buttons == 3 is only used for movement events
(for other events the trailing m/M marks a release instead), but in
normal mouse mode we can't tell so easily. So for that, look at the
previous event instead - if it is drag+release as well, then the current
event is a movement event.
so too early, before the mouse event was necessarily valid, so could end
up using the pane from the previous mouse event, or the active pane.
It is important that we use the right pane now that different panes can
have different key tables (for copy mode).
Fixes problem reported by Greg Hurrell.
supports them (that is, if it advertises itself as a VT420 - probably
just xterm). These are the vertical equivalent of the scroll region and
allow much faster scrolling of panes that do not take up the full width
of the terminal.
add a link of winlinks to each window and a pointer to the session to
each winlink. Also rewrite the alerts processing to return to the old
behaviour (alert in any window sets the flag on any winlink).
but there is also now a global command queue. Instead of command queues
being dispatched on demand from wherever the command happens to be
added, they are now all dispatched from the top level server
loop. Command queues may now also include callbacks as well as commands,
and items may be inserted after the current command as well as at the end.
This all makes command queues significantly more predictable and easier
to use, and avoids the complex multiple nested command queues used by
source-file, if-shell and friends.
A mass rename of struct cmdq to a better name (cmdq_item probably) is
coming.
support line editing and instead executes a command as soon as a
non-number key is pressed. Add a -N flag to command-prompt for the same
in copy mode. Reported by Theo Buehler.
The vi-copy and emacs-copy mode key tables are gone, and instead copy
mode commands are bound in one of two normal key tables ("copy-mode" or
"copy-mode-vi"). Keys are bound to "send-keys -X copy-mode-command". So:
bind -temacs-copy C-Up scroll-up
bind -temacs-copy -R5 WheelUpPane scroll-up
Becomes:
bind -Tcopy-mode C-Up send -X scroll-up
bind -Tcopy-mode WheelUpPane send -N5 -X scroll-up
This allows the full command parser and command set to be used - for
example, we can use the normal command prompt for searching, jumping,
and so on instead of a custom one:
bind -Tcopy-mode C-r command-prompt -p'search up' "send -X search-backward '%%'"
command-prompt also gets a -1 option to only require on key press, which
is needed for jumping.
The plan is to get rid of mode keys entirely, so more to come eventually.
pane-border-status is set to "top" or "bottom" (rather than "off"),
every pane has a permanent top or bottom border containing the text from
pane-border-format.
Based on a diff sent long ago by Jonathan Slenders, mostly rewritten and
simplified by me.
